General Information
- How To Use This Manual
- Troubleshooting Guidelines
- How To Use Troubleshooting/Inspection Service Points
- Troubleshooting Contents
- Notes
- 1. Standard Flow Of Diagnostic Troubleshooting
- 2. System Operation And Symptom Verification Tests
- 3. Diagnostic Function
- 4. Diagnostic Trouble Code Chart
- 5. Symptom Chart
- 6. Diagnostic Trouble Code Procedures
- 7. Symptom Procedures
- 8. Service Data Reference Table
- 9. Check At Ecu Terminals
- 10. Inspection Procedures Using An Oscilloscope
- How To Use The Inspection Procedures
- Connector Measurement Service Points
- Connector Inspection Service Points
- How To Cope With Intermittent Malfunctions
- Inspection Service Points For A Blown Fuse
- How To Treat Current Trouble
- How To Treat Past Trouble
- Troubleshooting Contents
- INTERSYSTEM Affiliated DTC Reference Table
- Vehicle Identification
- Precautions Before Service
- Supplemental Restraint System (SRS)
- How To Perform Vehicle Identification Number (VIN) Writing
- VIN Code Registration Procedure For ECM
Or Pcm - Initialization Procedure For Learning Value In MFI Engine
- Learning Procedure For Idling In MFI Engine
- Form-In-Place Gasket (FIPG)
- Servicing Electrical System
- Vehicle Washing
- Application Of Anti-Corrosion Agents And Undercoats
- Scan Tool (M.U.T.-III Sub Assembly)
- Bolts And Nuts With Stabilizer For Coefficient Of Friction
- Towing And Hoisting
- General Data And Specifications
- Tightening Torque
- Lubrication And Maintenance
- Recommended Lubricants And Lubricant Capacities Table
- Scheduled Maintenance Table
- Maintenance Service
- 1. Fuel System (Tank, Pipe Line And Connection, And Fuel Tank Filler Tube Cap) (Check For Leaks)
- 2. Fuel Hoses (Check Condition)
- 3. Air Cleaner Filter (Replace)
- 4. Evaporative Emission System (Except Evaporative Emission Canister) (Check For Clogging)
- 5. Spark Plugs (Replace)
- 6. Intake And Exhaust Valve Clearance [4G6-MIVEC Engine And 6G7-MIVEC Engine (Intake Side Only)] (Inspect And Adjust)
- 7. Timing Belt (Replace)
- 8. Drive Belts (For The Generator And Power Steering Pump) (Check)
- Drive Belt Tension Check <2.4L Engine>
- Generator Drive Belt Tension Check <3.8L Engine>
- <When Using Special Tool MB992080: Recommendation>
- <When Using The Tension Gauge>
- <Belt Deflection Check>
- Generator Drive Belt Tension Adjustment <3.8L Engine>
- Power Steering Drive Belt Tension Check <3.8L Engine>
- <When Using A Tension Gauge>
- Power Steering Drive Belt Tension Adjustment <3.8L Engine>
- 9. Exhaust System (Connections Portion Of Muffler, Muffler Pipes And Converter Heat Shields) (Check And Service As Required)
- 10. Engine Oil (Change)
- 11. Engine Oil Filter (Replace)
- 12. Manual Transmission Oil
- 13. Transmission Fluid
- 14. Engine Coolant (Change)
- 15. Coolant Hoses (Radiator Hose, Heater Hose) (Inspect)
- 16. Disc Brake Pads, Rotors (Inspect For Wear)
- 17. Brake Hoses (Check For Deterioration Or Leaks)
- 18. Ball Joint And Steering Linkage Seals (Inspect For Grease Leaks And Damage)
- 19. Drive Shaft Boots (Inspect For Grease Leaks And Damage)
- 20. Suspension System (Inspect For Looseness And Damage)
- 21. Tires (Rotate)
- Main Sealant And Adhesive Table