Engine Control System - VK45DE

• Index For DTC
  • DTC No. Index
  • Alphabetical Index
  • DTC Table
• Precautions
  • Precautions for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
  • On Board Diagnostic (OBD) System of Engine and A/T
  • Precaution
  • Wiring Diagrams and Trouble Diagnosis
• Preparation
  • Special Service Tools
  • Commercial Service Tools
• Engine Control System
  • System Diagram
  • Multiport Fuel Injection (MFI) System
    • Input/Output Signal Chart
    • System Description
    • Various Fuel Injection Increase/Decrease Compensation
    • Mixture Ratio Feedback Control (Closed Loop Control)
    • Open Loop Control
    • Mixture Ratio Self-Learning Control
    • Fuel Injection Timing
    • Sequential Multiport Fuel Injection System
    • Simultaneous Multiport Fuel Injection System
    • Fuel Shut-Off
  • Electronic Ignition (EI) System
    • Input/Output Signal Chart
    • System Description
  • Fuel Cut Control (at No Load and High Engine Speed)
    • Input/Output Signal Chart
    • System Description
• Air Conditioning Cut Control
  • Input/Output Signal Chart
  • System Description
• Automatic Speed Control Device (ASD)
  • System Description
    • Input/Output Signal Chart
    • Basic ASD System
    • Set Operation
    • ACCEL Operation
    • Cancel Operation
    • Coast Operation
    • Resume Operation
  • Component Description
    • ASD Steering Switch
    • ASD Brake Switch
    • Stop Lamp Switch
    • Electric Throttle Control Actuator
    • ASD Indicator
• Can Communication
  • System Description
• Evaporative Emission System
  • Description
    • System Description
    • Evaporative Emission Line Drawing
  • Component Inspection
    • EVAP Canister
    • Fuel Tank Vacuum Relief Valve (Built Into Fuel Fuller Cap)
    • EVAP Canister Purge Volume Control Solenoid Valve
    • Fuel Tank Temperature Sensor
    • EVAP Canister Vent Control Valve
    • EVAP Control System Pressure Sensor
    • EVAP Service Port
  • Removal and Installation
    • EVAP Canister
    • EVAP Canister Vent Control Valve
  • How to Detect Fuel Vapor Leakage
    • Notes
    • With Consult-II
    • Without Consult-II
• On Board Refueling Vapor Recovery (ORVR)
  • System Description
  • Diagnostic Procedure
    • Symptom: Fuel Odor From EVAP Canister Is Strong.
    • Symptom: Cannot Refuel/Fuel Odor From The Fuel Filler Opening Is Strong While Refueling.
  • Component Inspection
    • Refueling EVAP Vapor Cut Valve
      • With Consult-II
    • Without CONSULT-II
• Positive Crankcase Ventilation
  • Description
    • System Description
  • Component Inspection
    • PCV (Positive Crankcase Ventilation) Valve
    • PCV Valve Ventilation Hose
• IVIS (INFINITI Vehicle Immobilizer System-NATS)
  • Description
• On Board Diagnostic (OBD) System
  • Introduction
  • Two Trip Detection Logic
  • Emission-Related Diagnostic Information
    • Emission-Related Diagnostic Information Items
    • DTC And 1ST Trip DTC
    • How to Read DTC and 1st Trip DTC
      • Notes
      • With Consult-II
    • Freeze Frame Data And 1ST Trip Freeze Frame Data
    • System Readiness Test (SRT) Code
    • SRT Item
    • SRT Set Timing
    • SRT Service Procedure
    • How to Display SRT Status
      • With Consult-II
      • With GST
      • No Tools
    • How to Set SRT Code
      • Notes
      • With Consult-II
      • Without Consult-II
      • Driving Pattern
      • Suggested Transmission Gear Position
    • Test Value And Test Limit (GST Only - Not Applicable To Consult-II)
    • How To Erase Emission-Related Diagnostic Information
      • How to Erase DTC
  • Malfunction Indicator Lamp (MIL)
    • Description
    • On Board Diagnostic System Function
      • Notes
      • MIL Flashing Without DTC
    • How To Switch Diagnostic Test Mode
      • Notes
      • How to Set Diagnostic Test Mode II (Self-diagnostic Results)
      • How to Set Diagnostic Test Mode II (Heated Oxygen Sensor 1 Monitor)
      • How to Switch Monitored Sensor From Bank 1 to Bank 2 or Vice Versa
      • How to Erase Diagnostic Test Mode II (Self-diagnostic Results)
    • Diagnostic Test Mode I - Bulb Check
    • Diagnostic Test Mode I - Malfunction Warning
    • Diagnostic Test Mode II - Self-Diagnostic Results
      • Notes
      • How to Erase Diagnostic Test Mode II (Self-Diagnostic Results)
    • Diagnostic Test Mode II - Heated Oxygen Sensor 1 Monitor
  • OBD System Operation Chart
    • Relationship Between Mil, 1ST Trip DTC, And Detectable Items
    • Summary Chart
    • Relationship Between Mil, DTC, 1ST Trip DTC And Driving Patterns For "Misfire" < Exhaust Quality Deterioration>, "Fuel Injection System"
    • Explanation For Driving Patterns For "Misfire < Exhaust Quality Deterioration>", "Fuel Injection System"
      • < Driving Pattern B >
      • < Driving Pattern C>
    • Explanation For Driving Patterns Except For "Misfire < Exhaust Quality Deterioration >", "Fuel Injection System"
      • < Driving Pattern A >
      • < Driving Pattern B >
• Basic Service Procedure
  • Basic Inspection
  • Idle Speed and Ignition Timing Check
    • Idle Speed
      • With CONSULT-II
      • With GST
    • Ignition Timing
      • Notes
      • Method A
      • Method B
  • Idle Mixture Ratio Adjustment
    • Preparation
    • Overall Sequence
    • Detailed Procedure
  • VIN Registration
    • Description
    • Operation Procedure
      • With CONSULT-II
  • Accelerator Pedal Released Position Learning
    • Description
    • Operation Procedure
  • Throttle Valve Closed Position Learning
    • Description
    • Operation Procedure
  • Idle Air Volume Learning
    • Description
    • Preparation
    • Operation Procedure
      • With CONSULT-II
      • Without CONSULT-II
    • Diagnostic Procedure
  • Fuel Pressure Check
    • Fuel Pressure Release
      • With CONSULT-II
      • Without CONSULT-II
    • Fuel Pressure Check
• Trouble Diagnosis
  • Trouble Diagnosis Introduction
    • Introduction
    • Work Flow
      • Overall Sequence
      • Detailed Flow
    • Diagnostic Worksheet
      • Description
      • Worksheet Sample
  • DTC Inspection Priority Chart
  • Fail-Safe Chart
  • Symptom Matrix Chart
    • System - Basic Engine Control System
    • System - Engine Mechanical & Other
  • Engine Control Component Parts Location
  • Vacuum Hose Drawing
  • Circuit Diagram
  • ECM Harness Connector Terminal Layout
  • ECM Terminals and Reference Value
    • Preparation
    • ECM Inspection Table
  • CONSULT-II Function (ENGINE)
    • Function
    • Engine Control Component Parts/Control Systems Application
    • Inspection Procedure
    • Work Support Mode
      • Work Item
    • Self-Diag Results Mode
      • Self Diagnostic Item
      • Freeze Frame Data and 1st Trip Freeze Frame Data
    • Data Monitor Mode
      • Monitored Item
    • Data Monitor (Spec) Mode
      • Monitored Item
    • Active Test Mode
      • Test Item
    • DTC & SRT Confirmation Mode
      • SRT STATUS Mode
      • SRT WORK SUPPORT Mode
      • DTC WORK SUPPORT Mode
    • Real Time Diagnosis In Data Monitor Mode (Recording Vehicle Data)
      • Description
      • Operation
  • Generic Scan Tool (GST) Function
    • Description
    • Function
    • Inspection Procedure
  • CONSULT-II Reference Value in Data Monitor
  • Major Sensor Reference Graph in Data Monitor Mode
    • Notes
    • CLSD THL Pos, ACCEL Sen 1, THRTL Sen 1
    • Eng Speed, Mas A/F Se-B1, THRTL Sen 1, Ho2S2 (B1), Ho2S1 (B1), INJ Pulse-B1
• Trouble Diagnosis - Specification Value
  • Description
  • Testing Condition
  • Inspection Procedure
  • Diagnostic Procedure
    • Overall Sequence
    • Detailed Procedure
• Trouble Diagnosis For Intermittent Incident
  • Description
    • Notes
    • Common Intermittent Incidents Report Situations
  • Diagnostic Procedure
• Power Supply And Ground Circuit
  • Wiring Diagram
  • Diagnostic Procedure
  • Ground Inspection
• DTC U1000 & U1001: Can Communication Line
  • Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
  • Wiring Diagram
  • Diagnostic Procedure
• DTC P0011, P0021: IVT Control
  • Description
    • System Description
    • Component Inspection
      • Intake Valve Timing Control Solenoid Valve
      • Intake Valve Timing Control Position Sensor
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
    • Notes
    • Fail-Safe Mode
  • DTC Confirmation Procedure
    • Notes
    • Procedure For Malfunction A
      • With CONSULT-II
      • With GST
    • Procedure For Malfunction B
      • With CONSULT-II
      • With GST
  • Wiring Diagram
    • Bank 1
    • Bank 2
  • Diagnostic Procedure
  • Component Inspection
    • Intake Valve Timing Control Position Sensor
    • Intake Valve Timing Control Solenoid Valve
  • Removal and Installation
    • Intake Valve Timing Control Position Sensor
    • Intake Valve Timing Control Solenoid Valve
• DTC P0031, P0032, P0051, P0052: Ho2S1 Heater
  • Description
    • System Description
    • Operation
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
    • Bank 1
    • Bank 2
  • Diagnostic Procedure
  • Component Inspection
    • Heated Oxygen Sensor 1 Heater
  • Removal and Installation
    • Heated Oxygen Sensor 1
• DTC P0037, P0038, P0057, P0058: Ho2S2 Heater
  • Description
    • System Description
    • Operation
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
    • Bank 1
    • Bank 2
  • Diagnostic Procedure
  • Component Inspection
    • Heated Oxygen Sensor 2 Heater
  • Removal and Installation
    • Heated Oxygen Sensor 2
• DTC P0101: MAF Sensor
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • Procedure For Malfunction A
      • Notes
      • With CONSULT-II
      • With GST
    • Procedure For Malfunction B
      • Notes
      • With CONSULT-II
  • Overall Function Check
    • Procedure For Malfunction B
      • Notes
      • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Mass Air Flow Sensor
      • With CONSULT-II
      • Without CONSULT-II
  • Removal and Installation
    • Mass Air Flow Sensor
• DTC P0102, P0103: MAF Sensor
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
    • Notes
    • Fail-Safe Mode
  • DTC Confirmation Procedure
    • Notes
    • Procedure For DTC P0102
      • With CONSULT-II
      • With GST
    • Procedure For DTC P0103
      • With CONSULT-II
      • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Mass Air Flow Sensor
      • With CONSULT-II
      • Without CONSULT-II
  • Removal and Installation
    • Mass Air Flow Sensor
• DTC P0112, P0113: IAT Sensor
  • Component Description
    • Notes
    • < Reference data>
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Intake Air Temperature Sensor
  • Removal and Installation
    • Mass Air Flow Sensor
• DTC P0117, P0118: ECT Sensor
  • Component Description
    • Notes
    • < Reference data>
  • On Board Diagnosis Logic
    • Notes
    • Fail-Safe Mode
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Engine Coolant Temperature Sensor
  • Removal and Installation
    • Engine Coolant Temperature Sensor
• DTC P0122, P0123: TP Sensor
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
    • Notes
    • Fail-Safe Mode
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Throttle Position Sensor
  • Removal and Installation
    • Electric Throttle Control Actuator
• DTC P0125: ECT Sensor
  • Component Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Diagnostic Procedure
  • Component Inspection
    • Engine Coolant Temperature Sensor
  • Removal and Installation
    • Engine Coolant Temperature Sensor
• DTC P0127: IAT Sensor
  • Component Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Diagnostic Procedure
  • Component Inspection
    • Intake Air Temperature Sensor
  • Removal and Installation
    • Mass Air Flow Sensor
• DTC P0128: Thermostat Function
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Diagnostic Procedure
  • Component Inspection
    • Engine Coolant Temperature Sensor
  • Removal and Installation
    • Engine Coolant Temperature Sensor
• DTC P0132, P0152: Ho2S1
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
    • Bank 1
    • Bank 2
  • Diagnostic Procedure
  • Component Inspection
    • Heated Oxygen Sensor 1
      • With Consult-II
      • Without CONSULT-II
  • Removal and Installation
    • Heated Oxygen Sensor 1
• DTC P0133, P0153: Ho2S1
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
  • Overall Function Check
    • Notes
    • With GST
  • Wiring Diagram
    • Bank 1
    • Bank 2
  • Diagnostic Procedure
  • Component Inspection
    • Heated Oxygen Sensor 1
      • With Consult-II
      • Without CONSULT-II
  • Removal and Installation
    • Heated Oxygen Sensor 1
• DTC P0134, P0154: Ho2S1
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
  • Overall Function Check
    • Notes
    • With GST
  • Wiring Diagram
    • Bank 1
    • Bank 2
  • Diagnostic Procedure
  • Component Inspection
    • Heated Oxygen Sensor 1
      • With Consult-II
      • Without CONSULT-II
  • Removal and Installation
    • Heated Oxygen Sensor 1
• DTC P0138, P0158: Ho2S2
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
    • Bank 1
    • Bank 2
  • Diagnostic Procedure
  • Component Inspection
    • Heated Oxygen Sensor 2
      • With Consult-II
      • Without CONSULT-II
  • Removal and Installation
    • Heated Oxygen Sensor 2
• DTC P0139, P0159: Ho2S2
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
  • Overall Function Check
    • Notes
    • With GST
  • Wiring Diagram
    • Bank 1
    • Bank 2
  • Diagnostic Procedure
  • Component Inspection
    • Heated Oxygen Sensor 2
      • With Consult-II
      • Without CONSULT-II
  • Removal and Installation
    • Heated Oxygen Sensor 2
• DTC P0171, P0174: Fuel Injection System Function
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
    • Bank 1
    • Bank 2
  • Diagnostic Procedure
• DTC P0172, P0175: Fuel Injection System Function
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
    • Bank 1
    • Bank 2
  • Diagnostic Procedure
• DTC P0181: FTT Sensor
  • Component Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Fuel Tank Temperature Sensor
  • Removal and Installation
    • Fuel Tank Temperature Sensor
• DTC P0182, P0183: FTT Sensor
  • Component Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Fuel Tank Temperature Sensor
  • Removal and Installation
    • Fuel Tank Temperature Sensor
• DTC P0222, P0223: TP Sensor
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
    • Notes
    • Fail-Safe Mode
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Throttle Position Sensor
  • Removal and Installation
    • Electric Throttle Control Actuator
• DTC P0300 - P0308: Multiple Cylinder Misfire, No. 1 - 8 Cylinder Misfire
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Diagnostic Procedure
• DTC P0327, P0328, P0332, P0333: KS
  • Component Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Knock Sensor
  • Removal and Installation
    • Knock Sensor
• DTC P0335: CKP Sensor (Pos)
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Crankshaft Position Sensor (Pos)
  • Removal and Installation
    • Crankshaft Position Sensor (Pos)
• DTC P0340: Camshaft Position (CMP) Sensor (Phase)
  • Component Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Camshaft Position Sensor
  • Removal and Installation
    • Camshaft Position Sensor (Phase)
• DTC P0420, P0430: Three Way Catalyst Function
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
  • Overall Function Check
    • Notes
    • With GST
  • Diagnostic Procedure
• DTC P0441: EVAP Control System
  • System Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
  • Overall Function Check
    • Notes
    • With GST
  • Diagnostic Procedure
• DTC P0442: EVAP Control System
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Diagnostic Procedure
• DTC P0444, P0445: EVAP Canister Purge Volume Control Solenoid Valve
  • Description
    • System Description
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • EVAP Canister Purge Volume Control Solenoid Valve
      • With CONSULT-II
      • Without CONSULT-II
  • Removal and Installation
    • EVAP Canister Purge Volume Control Solenoid Valve
• DTC P0447: EVAP Canister Vent Control Valve
  • Component Description
    • Notes
    • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With CONSULT-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • EVAP Canister Vent Control Valve
      • With CONSULT-II
      • Without CONSULT-II
• DTC P0451: EVAP Control System Pressure Sensor
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With CONSULT-II
    • With GST
  • Diagnostic Procedure
  • Component Inspection
    • EVAP Control System Pressure Sensor
• DTC P0452: EVAP Control System Pressure Sensor
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With CONSULT-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • EVAP Control System Pressure Sensor
• DTC P0453: EVAP Control System Pressure Sensor
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With CONSULT-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • EVAP Control System Pressure Sensor
• DTC P0455: EVAP Control System
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Diagnostic Procedure
• DTC P0456: EVAP Control System
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
  • Overall Function Check
    • With GST
  • Diagnostic Procedure
• DTC P0460: Fuel Level Sensor
  • Component Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Diagnostic Procedure
  • Removal and Installation
    • Fuel Level Sensor
• DTC P0461: Fuel Level Sensor
  • Component Description
  • On Board Diagnosis Logic
  • Overall Function Check
    • Notes
    • With Consult-II
    • With GST
  • Diagnostic Procedure
  • Removal and Installation
    • Fuel Level Sensor
• DTC P0462, P0463: Fuel Level Sensor Circuit
  • Component Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Diagnostic Procedure
  • Removal and Installation
    • Fuel Level Sensor
• DTC P0500: VSS
  • Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
  • Overall Function Check
    • Notes
    • With GST
  • Diagnostic Procedure
• DTC P0506: ISC System
  • Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Diagnostic Procedure
• DTC P0507: ISC System
  • Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Diagnostic Procedure
• DTC P0550: PSP Sensor
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Power Steering Pressure Sensor
  • Removal and Installation
    • Power Steering Pressure Sensor
• DTC P0605: ECM
  • Component Description
  • On Board Diagnosis Logic
    • Notes
    • Fail-Safe Mode
  • DTC Confirmation Procedure
    • Notes
    • Procedure For Malfunction A
      • With CONSULT-II
      • With GST
    • Procedure For Malfunction B
      • With CONSULT-II
      • With GST
    • Procedure For Malfunction C
      • With CONSULT-II
      • With GST
  • Diagnostic Procedure
• DTC P1065: ECM Power Supply
  • Component Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
• DTC P1111, P1136: IVT Control Solenoid Valve
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
    • Bank 1
    • Bank 2
  • Diagnostic Procedure
  • Component Inspection
    • Intake Valve Timing Control Solenoid Valve
  • Removal and Installation
    • Intake Valve Timing Control Solenoid Valve
• DTC P1121: Electric Throttle Control Actuator
  • Component Description
  • On Board Diagnosis Logic
    • Notes
    • Fail-Safe Mode
  • DTC Confirmation Procedure
    • Notes
    • Procedure For Malfunction A And B
      • With CONSULT-II
      • With GST
    • Procedure For Malfunction C
      • With CONSULT-II
    • With GST
  • Diagnostic Procedure
• DTC P1122: Electric Throttle Control Function
  • Description
  • On Board Diagnosis Logic
    • Notes
    • Fail-Safe Mode
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Throttle Control Motor
  • Removal and Installation
    • Electric Throttle Control Actuator
• DTC P1124, P1126: Throttle Control Motor Relay
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
    • Notes
    • Fail-Safe Mode
  • DTC Confirmation Procedure
    • Notes
    • Procedure For DTC P1124
      • Notes
      • With CONSULT-II
      • With GST
    • Procedure For DTC P1126
      • With CONSULT-II
      • With GST
  • Wiring Diagram
  • Diagnostic Procedure
• DTC P1128: Throttle Control Motor
  • Component Description
  • On Board Diagnosis Logic
    • Notes
    • Fail-Safe Mode
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Throttle Control Motor
  • Removal and Installation
    • Electric Throttle Control Actuator
• DTC P1140, P1145: IVT Control Position Sensor
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
    • Bank 1
    • Bank 2
  • Diagnostic Procedure
  • Component Inspection
    • Intake Valve Timing Control Position Sensor
  • Removal and Installation
    • Intake Valve Timing Control Position Sensor
• DTC P1143, P1163: Ho2S1
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
  • Overall Function Check
    • Notes
    • With GST
  • Diagnostic Procedure
  • Component Inspection
    • Heated Oxygen Sensor 1
      • With CONSULT-II
      • Without CONSULT-II
  • Removal and Installation
    • Heated Oxygen Sensor 1
• DTC P1144, P1164: Ho2S1
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
  • Overall Function Check
    • Notes
    • With GST
  • Diagnostic Procedure
  • Component Inspection
    • Heated Oxygen Sensor 1
      • With CONSULT-II
      • Without CONSULT-II
  • Removal and Installation
    • Heated Oxygen Sensor 1
• DTC P1146, P1166: Ho2S2
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
  • Overall Function Check
    • Notes
    • With GST
  • Wiring Diagram
    • Bank 1
    • Bank 2
  • Diagnostic Procedure
  • Component Inspection
    • Heated Oxygen Sensor 2
      • With CONSULT-II
    • Without CONSULT-II
  • Removal and Installation
    • Heated Oxygen Sensor 2
• DTC P1147, P1167: Ho2S2
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
  • Overall Function Check
    • Notes
    • With GST
  • Wiring Diagram
    • Bank 1
    • Bank 2
  • Diagnostic Procedure
  • Component Inspection
    • Heated Oxygen Sensor 2
      • With CONSULT-II
      • Without CONSULT-II
  • Removal and Installation
    • Heated Oxygen Sensor 2
• DTC P1148, P1168: Closed Loop Control
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
  • Overall Function Check
    • Notes
    • With GST
  • Diagnostic Procedure
• DTC P1211: TCS Control Unit
  • Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Diagnostic Procedure
• DTC P1212: TCS Communication Line
  • Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Diagnostic Procedure
• DTC P1217: Engine Over Temperature
  • Description
    • System Description
      • Notes
      • Cooling Fan Control
      • Cooling Fan Operation
      • Cooling Fan Relay Operation
    • Component Description
      • Cooling Fan Motor
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • Overall Function Check
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
    • Notes
    • Procedure A
    • Procedure B
  • Main 12 Causes of Overheating
  • Component Inspection
    • Cooling Fan Motor
• DTC P1225: TP Sensor
  • Component Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Diagnostic Procedure
  • Removal and Installation
    • Electric Throttle Control Actuator
• DTC P1226: TP Sensor
  • Component Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Diagnostic Procedure
  • Removal and Installation
• DTC P1229: Sensor Power Supply
  • On Board Diagnosis Logic
    • Notes
    • Fail-Safe Mode
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
• DTC P1444: EVAP Canister Purge Volume Control Solenoid Valve
  • Description
    • System Description
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • EVAP Canister Purge Volume Control Solenoid Valve
      • With CONSULT-II
      • Without CONSULT-II
  • Removal and Installation
    • EVAP Canister Purge Volume Control Solenoid Valve
• DTC P1446: EVAP Canister Vent Control Valve
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • EVAP Canister Vent Control Valve
      • With CONSULT-II
    • Without CONSULT-II
• DTC P1564: ICC Steering Switch
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • ICC Steering Switch
• DTC P1564: ASD Steering Switch
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • ASD Steering Switch
• DTC P1568: ICC Function
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Diagnostic Procedure
• DTC P1572: ICC Brake Switch
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • ICC Brake Switch
    • Stop Lamp Switch
    • ICC Brake Hold Relay
• DTC P1572: ASD Brake Switch
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • ASD Brake Switch
    • Stop Lamp Switch
• DTC P1574: ICC Vehicle Speed Sensor
  • Component Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Diagnostic Procedure
• DTC P1574: ASD Vehicle Speed Sensor
  • Component Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Diagnostic Procedure
• DTC P1706: PNP Switch
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
  • Overall Function Check
    • Notes
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
• DTC P1720: VSS
  • Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Diagnostic Procedure
• DTC P1780: Shift Change Signal
  • Description
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Diagnostic Procedure
• DTC P1800: VIAS Control Solenoid Valve
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • VIAS Control Solenoid Valve
      • With Consult-II
      • Without CONSULT-II
  • Removal and Installation
    • VIAS Control Solenoid Valve
• DTC P1805: Brake Switch
  • Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
    • Notes
    • Fail-Safe Mode
  • DTC Confirmation Procedure
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Stop Lamp Switch
• DTC P2122, P2123: App Sensor
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
    • Notes
    • Fail-Safe Mode
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Accelerator Pedal Position Sensor
  • Removal and Installation
    • Accelerator Pedal
• DTC P2127, P2128: App Sensor
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
    • Notes
    • Fail-Safe Mode
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Accelerator Pedal Position Sensor
  • Removal and Installation
    • Accelerator Pedal.
• DTC P2135: TP Sensor
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
    • Notes
    • Fail-Safe Mode
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Throttle Position Sensor
  • Removal and Installation
    • Electric Throttle Control Actuator
• DTC P2138: App Sensor
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • On Board Diagnosis Logic
    • Notes
    • Fail-Safe Mode
  • DTC Confirmation Procedure
    • Notes
    • With Consult-II
    • With GST
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Accelerator Pedal Position Sensor
  • Removal and Installation
    • Accelerator Pedal
• Variable Induction Air Control System (VIAS)
  • Description
    • System Description
    • Component Description
      • Power Valve
      • VIAS Control Solenoid Valve
  • CONSULT-II Reference Value in Data Monitor Mode
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • VIAS Control Solenoid Valve
      • With Consult-II
      • Without CONSULT-II
    • Vacuum Tank
  • Removal and Installation
    • VIAS Control Solenoid Valve
• Ignition Signal
  • Component Description
    • Ignition Coil & Power Transistor
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Ignition Coil With Power Transistor
    • Condenser
  • Removal and Installation
    • Ignition Coil With Power Transistor
• Injector Circuit
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Injector
  • Removal and Installation
    • Injector
• Fuel Pump Circuit
  • Description
    • System Description
    • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Fuel Pump
  • Removal and Installation
    • Fuel Pump
• Refrigerant Pressure Sensor
  • Component Description
  • Wiring Diagram
  • Diagnostic Procedure
  • Removal and Installation
    • Refrigerant Pressure Sensor
• Electrical Load Signal
  • Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • Diagnostic Procedure
• ICC Brake Switch
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • ICC Brake Switch
    • Stop Lamp Switch
    • ICC Brake Hold Relay
• ASD Brake Switch
  • Component Description
  • Consult-II Reference Value In Data Monitor Mode
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • ASD Brake Switch
    • Stop Lamp Switch
• ASD Indicator
  • Component Description
  • CONSULT-II Reference Value in Data Monitor Mode
  • Wiring Diagram
  • Diagnostic Procedure
• Snow Mode Switch
  • Description
  • CONSULT-II Reference Value in the Data Monitor Mode
  • Wiring Diagram
  • Diagnostic Procedure
  • Component Inspection
    • Snow Mode Switch
• Mil And Data Link Connector
  • Wiring Diagram
• Service Data And Specifications (SDS)
  • Fuel Pressure
  • Idle Speed and Ignition Timing
  • Calculated Load Value
  • Mass Air Flow Sensor
  • Intake Air Temperature Sensor
  • Engine Coolant Temperature Sensor
  • Fuel Tank Temperature Sensor
  • Crankshaft Position Sensor (POS)
  • Camshaft Position Sensor (PHASE)
  • Heated Oxygen Sensor 1 Heater
  • Heated Oxygen sensor 2 Heater
  • Throttle Control Motor
  • Injector
  • Fuel Pump